Skip to main content

6mm and 6.5 Creedmoor Precision Ammo Reloading

The 6.5 Creedmoor and 6mm Creedmoor ammo cartridges are capable of incredible accuracy, making them prime candidates for reloading

6mm and 6.5 Creedmoor Precision Ammo Reloading

When hand reloading precision 6.5mm Creedmoor and 6mm Creedmoor ammo cartridges, you’ll need quality loading equipment and components.

When precision reloading for a super-accurate rifle — such as a 6mm Creedmoor or 6.5 Creedmoor — achieving half-minute-of-angle accuracy comes easily with nothing more than standard reloading tools and unmodified, off-the-shelf components. From that point on, though, improvements in accuracy come slowly and usually in very small increments. Some things we do will prove to be more important than others, but each and every one can contribute to minor improvements in group size. A bit here and a bit there, and groups smaller than you thought possible will eventually begin to appear on your targets. Some rifles respond nicely to some things we do, while others appear not to notice. Try hard enough with the right equipment and suddenly you are approaching—or are perhaps even inside—the elusive quarter-minute barrier.

Custom-built Remington 700 chambered for the popular 6.5 creedmoor.
With its blueprinted Remington Model 700 action, Bartlein 28-inch switch barrel, McMillan stock, Jewell 2-ounce trigger, Nightforce 12-42x 56mm scope, Talley tactical rings, and 20-MOA Picatinny base, Layne’s custom rifle was originally built by Lex Webernick of Rifles Inc. It weighs a “feathery” 16.75 pounds.

When asked to write an article on precision loading the 6mm Creedmoor and 6.5 Creedmoor ammo cartridges, I immediately knew which of my rifles was up to the task. It was built by Lex Webernick of Rifles Inc. on a blueprinted Remington 700 action, and it was his idea of the perfect rifle for sitting at a portable bench-rest and surprising rockchucks at extremely long distances. With a Nightforce 12-42x56mm scope in Talley 30mm tactical rings and a 20-MOA Picatinny rail, it weighs a “feathery” 20.5 pounds. The rifle has a McMillan benchrest stock and a Jewell 2-ounce trigger. Its original 28-inch Shilen barrel measures an inch in diameter at the muzzle, and it is chambered for the old 6mm-284 wildcat. When the barrel was new, it consistently shot five bullets inside 0.300 inch, and occasional groups in the low 0.2s and high 0.1s never surprised me. I eventually converted the outfit into a switch-barrel rifle with barrels in various calibers, and the two Creedmoor chamberings are a couple of its latest additions.

The Bartlein barrels in 6mm Creedmoor and 6.5 Creedmoor are also 28 inches long, but to keep total weight of the rifle just under 17 pounds, they are the lighter Heavy Varmint contour. Rifling twist rates are 1:7 for the 6mm and 1:8 for the 6.5. Prior to coming up with chamber neck diameters of the two barrels, I decided which brass would be used. I chose Lapua brass for several reasons, not the least of which is the ability to withstand many maximum-pressure firings. With 0.264-inch bullets seated, neck diameter ranged from 0.2912 to 0.2923 inch, so all cases were outside-turned to 0.291 inch. When Lapua 6.5mm Creedmoor cases were necked down for 0.243-inch bullets, neck diameter ranged from 0.2716 to 0.2730 inch, and the necks of those cases were turned to 0.271 inch.

Chamber neck diameters of 0.275 inch for the 6mm and 0.295 inch for the 6.5mm allow me to shoot factory ammo in both barrels. While S.A.A.M.I. maximum neck diameters of the 6mm Creedmoor and 6.5 Creedmoor cartridges are 0.275 and 0.295 inch, most factory ammo runs from 0.271 to 0.273 inch for the 6mm and 0.290 to 0.292 inch for the 6.5mm. To make certain factory ammo is safe to fire in my rifle, I drop each cartridge into a custom gauge made by reaming out a couple of cavities in a Lyman Ammo Checker with the reamers that were used to cut the chambers in my barrels. Chamber throat diameters for my two barrels are 0.2435 and 0.2645 inch.


Trimming 6mm Creedmoor and 6.5 Creedmoor brass for reloading
After virgin cases are full-length resized, they are all trimmed to the exact same length, and they are kept at that length throughout their service life.

6mm and 6.5 Creedmoor Case Prep is Critical

Squeezing the smallest groups possible from an extremely accurate rifle requires a great deal of time in the preparation of cartridge cases. The goal is to transform an affordable, mass-produced product into a bullet-launching system that is as concentric as the receiver, bolt, firing pin, and barrel of a precision-built rifle. First on the agenda is a thorough examination of each case for imperfections, such as cracks, dents, deep scratches, and off-center flash holes. Prior to running cases through a full-length resizing die, the body of each receives a light coat of Imperial case sizing wax, and the inside of its neck gets lightly coated with Imperial dry lube. All cases are trimmed to precisely the same length, and they are kept there throughout their service life.


Tests performed years ago by Sinclair International founder Fred Sinclair revealed that a primer seating variation of only 0.010 inch can vary firing pin strike energy by as much as 20 percent, so primer pockets are uniformed in depth, and their rounded corners are leveled for uniform primer fit with a Redding carbide cutter. A Lyman E-ZEE Prime tool is used for seating primers. Case-prep steps such as trimming, deburring, and chamfering necks are nicely handled by a Hornady Lock-N-Load Case Prep Center that has seven rotating stations. The Hornady case-prep machine also uniforms primer pockets, and my Redding carbide cutter with 8-32 threaded shank is a perfect fit for one of its stations. Redding, Sinclair International, Hornady, and other companies offer attachment adaptors for using their uniforming cutters with a handheld electric drill or screwdriver, but I prefer using the case-prep center.

There is one step I prefer to do by hand. The punch used to form the flash hole of a case at the factory sometimes leaves a small burr inside the case that can constrict primer flame during firing. The burr is not often seen in cases made by Lapua, but I do like to use the tool to cut a light bevel on the inner edge of the flash hole. Lyman, RCBS, Hornady, Forster, Sinclair International, and other companies offer this type of tool, but Redding is the only source I am aware of that has one sized specifically for the 0.059-inch flash hole of Lapua cases.

Uniforming neck wall thickness accomplishes two things. It closely aligns the axes of the bullet and the case, and equally important, it makes neck tension on bullets pretty much the same for the entire batch of cases. That goes a long way toward keeping velocity spread low. As mentioned earlier, case necks are outside-turned to 0.271 inch for the 6mm Creedmoor barrel and 0.291 inch for the 6.5 Creedmoor barrel.

Several types of tools are available for turning case necks. One of the first I bought during the 1960s was an attachment made by Forster for its case trimmer, and it still works great. Lyman and RCBS also offer the same type of turner for their trimmers, and they, as well as the Forster unit, can be used with an electric drill or screwdriver. At about that same time, I bought a hand tool from the late Paul Marquart, and it also is still going strong. Hand tools are now available from Sinclair, RCBS, Forster, and others, and while they are popular among short-distance benchrest competitors, if used alone they cease to be fun very quickly when a large quantity of cases is to be prepped.


Turning outside necks on 6mm Creedmoor and 6.5 Creedmoor cases for reloading
Case necks were outside-turned for diameters with bullets seated of 0.271 inch for the 6mm Creedmoor and 0.291 inch for the 6.5 Creedmoor. Respective chamber neck diameters of the two barrels are 0.275 and 0.295 inch.

Replacing hand power with electrical power eases the pain, and anything that runs in the 400 to 500 RPM range works perfectly. The 1/4-inch hex shaft of the Sinclair case driver (No. 749-002-109WB) works with a power drill or an electric screwdriver, and it accepts Sinclair case holders available for cartridges of various rim diameters (No. 749-002-493B is for the Creedmoor case). Simply clamp the power tool into a padded bench vise, turn on the juice, and use the small hand tool to turn case necks. Rather than having a single tool for several rifles, I have one devoted to each rifle that requires neck-turned cases. That eliminates the hassle of continuously adjusting the cutter blade on a single unit for several rifles. Set the cutter one time, lock it down, and it stays there until the cows come home. Hornady’s bench-mounted Neck Turn Tool is also quite good, and the 0.0005-inch clicks of its cutter adjustment knob make it fairly easy to record the correct settings for several rifle/cartridge combinations and then return to whatever setting is needed.

Regardless of which unit is used, a snug fit between the inside of the case neck and the turner mandrel is important. The mandrel should be only 0.0005 to 0.001 inch smaller than the inside of the case neck. The easiest way to achieve such precision is to run each case through a Sinclair expander die. Its 7/8-14 threads work with any reloading press. And don’t forget to lightly lube the turner mandrel and outside of the case neck with Imperial sizing die wax prior to turning each case.

Fit between case and chamber is closest after the case has been fired, and I prefer to leave it that way as long as possible by neck sizing only with a Redding Competition die with interchangeable bushings of various sizes. When cases are new, I start with a bushing 0.001 inch smaller than the neck diameter of the case with bullet seated, and if velocity spread is not as low as I think it should be, I try 0.002- and 0.003-inch bushings. After a number of firings, a slight resistance to bolt closure tells me that putting the squeeze on cases is needed, and for that I use a Redding body die that full-length resizes and bumps back the shoulder of the case without disturbing its neck. Moving the shoulder back 0.002 inch is usually plenty, and caliper-attached tools like the RCBS Precision Mic, Hornady’s Headspace Comparator, the Instant Headspace Indicator from Redding, and Sinclair’s Bump Gauge make doing so easy. If you’d rather not use one of those, a set of Shoulder Bump Shellholders from Redding vary 0.002 inch in thickness, and they work well.


Reloading dies for 6mm Creedmoor and 6.5 Creedmoor ammo
The author used Redding die sets for 6.5 Creedmoor and 6mm Creedmoor ammo handloading. The body die (left) full-length resizes a case and bumps back its shoulder the required amount without disturbing its neck. The Competition Seating Die (center) is used for seating bullets, and the Competition Neck Sizing die (right) has interchangeable bushings that squeeze down the neck of a case by the desired amount.

Some believe in weight-sorting cases, while others consider it to be a waste of time. As popular opinion among the former group has it, a heavier case has less capacity than a lighter case due to more material retained during the forming process. To see if weight differences are accurate indications of capacity differences, I weighed each of a batch of fired cases and then weighed each of them again when filled to the brim with water. Cases weighing precisely the same when empty varied in weight up to a full grain when filled with water. That makes capacity-sorting much more beneficial. Water can be used, and after the cases are emptied, they are placed in an electric dryer that most of us who use a sonic cleaner already have. For those who prefer to capacity-sort primed virgin brass, using an extremely dense powder, such as BLC-(2) instead of water, works equally well. I use an MTM Universal Powder Funnel Set with its 4-inch drop tube to fill a case to overflow with powder and then slide the mouth of the funnel across the mouth of the case to scrape the overflow into a small container.

Repeatedly firing and resizing the neck of a case work-hardens it, and the harder it becomes, the more neck tension will vary among a batch of cases. Variations in the amount of tension applied to bullets will cause velocity spread to increase. Annealing the necks of cases is the answer, and some competitors do so after each firing. Machines, such as the Annealeez and Anneal-Rite, use propane torches, while the Annealing Made Perfect unit from Brownells heats case necks by electrical induction. My home-built process works as well but is a bit slower. Regardless of which method is used, it is important to remember that allowing anything but the neck of a case to become extremely hot is an easy way to blow a rifle to smithereens.

Ideal Powders for 6mm and 6.5 Creedmoor Reloading

The ideal powder for 6mm Creedmoor and 6.5 Creedmoor reloading fills the case to the base of a seated bullet with a bit of compaction and no unfilled space. It reduces bullet jacket fouling in all barrels, and it virtually eliminates it in a barrel with an extremely smooth bore. The ideal propellant is also less sensitive to extremes in ambient temperature than many other powders. All of those characteristics are great contributors to achieving velocity spreads inside 10 fps, which is absolutely essential for minimal vertical shot distribution at extremely long range. The fact that H4350 meets those criteria explains why it is probably the single most popular powder among competitors who shoot the Creedmoor pair.

But IMR 4451 is nipping at its heels. While load data between the two powders is not interchangeable, their burn rates are quite close, and their bulk densities are virtually the same. Like H4350, IMR 4451 also reduces bullet jacket fouling and is minimally sensitive to changes in temperature. If a rifle fails to deliver top accuracy with one of those, it probably won’t do so with any propellant. An RCBS ChargeMaster Lite dispenses my powder charges, and each is checked on a laboratory-grade 304 scale that was made by Ohaus for RCBS during the 1980s.

Powder charge scales for 6mm Creedmoor and 6.5 Creedmoor ammo reloading
Each powder charge for 6.5 Creedmoor and 6mm Creedmoor reloading was dispensed by an RCBS ChargeMaster Lite and then checked on a laboratory-grade 304 scale that was once made for RCBS by Ohaus.

Notes on Seating 6mm and 6.5 Creedmoor Bullets

All the effort involved in achieving perfect concentricity in a rifle and its cases is wasted if bullets are seated out of alignment with the bore of the barrel. The goal to shoot for is less than 0.002 inch of runout on loaded rounds, and less than 0.001 inch is possible. This can only be accomplished on a consistent basis with precision bulletseating dies. The Wilson inline die from Brownells is quite good, and most short-range benchrest shooters use it or something similar. But it is used with an arbor press, and that makes it slower than dies used in a bench press. Among those, the Redding Competition Seating dies I am using with the two Creedmoor cartridges are working very well for me. Dies of similar design are available from Forster, RCBS, and Hornady. The Corbin CSP-1 bullet-swaging press can be used to load ammunition, and it is far more precisely built than a standard single-stage press—as it should be at $700. Precision ammo loaded on mine has less runout, and that makes it a bargain.

Hollowpoint bullets of the same caliber and weight from the same company vary slightly in length, and that makes recording overall cartridge length less accurate than recording a measurement from the head of the cartridge case to an arbitrary point on the ogive of the bullet (CHTO). Hornady’s Lock-N-Load bullet comparator attached to a digital caliper handles that job nicely.

Universal bulletseating stems that come in dies from various companies work fine with a variety of bullet profiles, but some are unsuitable for use with match bullets having extremely long ogives. Redding began offering stems shaped specifically for that type of bullet not long after ballistician Bill Davis came up with the VLD (very low drag) design. Hornady offers stems for ELD Match bullets of various calibers, and they are also compatible with the A-Max design, as well as some of the match bullets from other companies. RCBS and Forster offer special stems on request. If your seater die is leaving a ring on bullets, 400-grit emery cloth on the end of a sharpened wooden pencil will smooth the transition edge of its stem.

Due to slight dimensional variations in the ogives of a batch of bullets of the same caliber and weight from the same manufacturer, their free-travel distances will vary slightly during firing. Measurements taken from the base to an arbitrary point on the ogive of match bullets will vary as much as 0.005 inch, and that can increase velocity spread. Sorting bullets into batches with each batch having the same base-to-ogive dimension eliminates that variation, and the Sinclair Quick Bullet Sorting Stand is absolutely the best tool I have tried for accomplishing that.

When setting up the device, simply drop a bullet nose first into the holder and adjust the dial indicator up and down on its support post until it reads close to zero and then rotate the dial to exact zero. Small containers are used to sort bullets into groups that vary 0.0005 inch, and the groups of bullets are kept separate throughout the loading and firing processes. Bryan Litz of Berger Bullets considers this type of sorting to be the most beneficial thing that can be done to a bullet. Some folks incorrectly describe this as sorting by bearing surface length, but regardless of what it is called, it shrinks long-distance group size.

Match-grade barrels don’t come cheap, so rather than trying every bullet on the planet for this project, I chose four in each of the two Creedmoor calibers. All are accurate enough to win matches. In the precision-shooting games, shooter ability is far more important than the mechanical accuracy of a rifle, but having an accurate rifle and load are essential ingredients in the pie. And even if you don’t shoot competitively, your life will never again be the same after that incredibly small group appears on your 500- or 1,000-yard target.

GET THE NEWSLETTER Join the List and Never Miss a Thing.

Recommended Articles

See More Recommendations

Popular Videos

Mossberg Patriot Predator 6.5 PRC Rifle Review

Mossberg Patriot Predator 6.5 PRC Rifle Review

RifleShooter Magazine editor Scott Rupp breaks down all the features of the Mossberg Patriot Predator rifle chambered in 6.5 PRC.

Ruger Launches New American Rifle Predator in 6.5 Grendel

Ruger Launches New American Rifle Predator in 6.5 Grendel

OSG's Lynn Burkhead and Ruger's Matt WIlson kick off SHOT Show 2018 by taking a look at the Ruger Predator.

Black Hills Evolution of Rifle Cartridge: .308 Win. 175 Gr. Match

Black Hills Evolution of Rifle Cartridge: .308 Win. 175 Gr. Match

David Fortier talks with Jeff Hoffman of Black Hills Ammunition about the evolution of the .308 Win. 175 Gr. Match bullet.

Hornady 6MM Creedmoor

Hornady 6MM Creedmoor

Tom Beckstrand and Neal Emery of Hornady highlight the 6MM Creedmoor ammo.

See More Popular Videos

Trending Articles

The Christensen Arms lightweight Mesa Titanium Edition bolt-action hunting rifle is a peak performer.Christensen Arms Mesa Titanium Edition Rifle Review Reviews

Christensen Arms Mesa Titanium Edition Rifle Review

Brad Fitzpatrick - August 14, 2020

The Christensen Arms lightweight Mesa Titanium Edition bolt-action hunting rifle is a peak...

The new Hammerli TAC R1 22 C, an AR-15 style .22 rimfire rifle, is the first product in the company's new Defense line.Hammerli TAC R1 22 C Review Reviews

Hammerli TAC R1 22 C Review

James Tarr - August 12, 2020

The new Hammerli TAC R1 22 C, an AR-15 style .22 rimfire rifle, is the first product in the...

A .22LR rimfire rifle is a must-own for any gun owner, and these six bolt-action rimfire rifles give shooters a variety of offerings to choose from.6 Great Rimfire Bolt-Action Rifles Rimfire

6 Great Rimfire Bolt-Action Rifles

Jeff John - July 22, 2020

A .22LR rimfire rifle is a must-own for any gun owner, and these six bolt-action rimfire...

For decades, things were quiet on the .22 centerfire front. Starting in 2017, shooters were offered not one but two hot new centerfire .22 cartridges. First out of the gate was the .22 Nosler, followed by the Federal .224 Valkrie..22 Nosler vs .224 Valkyrie Ammo

.22 Nosler vs .224 Valkyrie

Brad Fitzpatrick - May 02, 2019

For decades, things were quiet on the .22 centerfire front. Starting in 2017, shooters were...

See More Trending Articles

More Reloading

With the right components, 33 Nosler handloads shine for hunting elk, moose, bears, and just about almost any big game; here's some valuable Nosler load data to get you started.33 Nosler Load Data Reloading

33 Nosler Load Data

Bryce M. Towsley - December 05, 2019

With the right components, 33 Nosler handloads shine for hunting elk, moose, bears, and just...

Jospeh von Benedikt conducts a test to see if match-grade primers really make a difference.Match-Grade Rifle Primers: Are They Better and Worth the Extra Expense? Reloading

Match-Grade Rifle Primers: Are They Better and Worth the Extra Expense?

Joseph von Benedikt - July 21, 2020

Jospeh von Benedikt conducts a test to see if match-grade primers really make a difference.

When a cartridge is fired, a progressive burn of the propellant converts it to rapidly expanding gas that exerts an equal amount of pressure in all directions. Maximum recommended pressure for a rifle cartridge is usually dictated by the action strength of the rifle for which it is developed.What Affects Rifle Chamber Pressure and Critical Factors You Need to Know Reloading

What Affects Rifle Chamber Pressure and Critical Factors You Need to Know

Layne Simpson - June 07, 2018

When a cartridge is fired, a progressive burn of the propellant converts it to rapidly...

Hodgdon CFE BLK powder - a Copper Fouling Eraser propellant - is perfect for 17 Hornet, 17 Ackley Hornet, 17 Fireball, 218 Bee and 221 Fireball handholds.Hodgdon CFE BLK: Best Varmint Cartridge Loads

Hodgdon CFE BLK: Best Varmint Cartridge Loads

Layne Simpson

Hodgdon CFE BLK powder - a Copper Fouling Eraser propellant - is perfect for 17 Hornet, 17...

See More Reloading

Magazine Cover

GET THE MAGAZINE Subscribe & Save

Digital Now Included!

SUBSCRIBE NOW

Give a Gift   |   Subscriber Services

PREVIEW THIS MONTH'S ISSUE Arrow

Buy Digital Single Issues

Don't miss an issue.
Buy single digital issue for your phone or tablet.

Buy Single Digital Issue on the RifleShooter App

Other Magazines

Special Interest Magazines

See All Special Interest Magazines

GET THE NEWSLETTER Join the List and Never Miss a Thing.

Phone Icon

Get Digital Access.

All RifleShooter subscribers now have digital access to their magazine content. This means you have the option to read your magazine on most popular phones and tablets.

To get started, click the link below to visit mymagnow.com and learn how to access your digital magazine.

Get Digital Access

Not a Subscriber?
Subscribe Now